Snowmobile

TABLE OF CONTENTS

Angle Finder (p/n 0644-097)
Ball Hone (p/n 0644-290, 291, 292, 293, 294)
Coolant Cap (Non-Pressurized) (p/n 0644-156)
Fan Spanner Wrench (Suzuki) (p/n 0644-340)
Flywheel Spanner Wrench (p/n 0144-007)
Duck-Foot T-Handle Wrench (8 mm) (p/n 0644-332)
EFI Throttle Cable Jam Nut/Oil-Injection Pump Jam Nut Wrench (p/n 0644-242)
Engine Stand (p/n 0644-079)
Exhaust Spring Pliers (p/n 0644-391,397)
Crankshaft Protector Cap (p/n 0644-234)
Flywheel Puller (p/n 0744-040)
Flywheel Puller (p/n 0644-480)
Flywheel Puller Insert (p/n 0644-179)
Crankshaft Bearing Remover (p/n 0144-302)
Idle Speed Screw Jam Nut Wrench (p/n 0644-311)
Linkage Wrench (8 mm) (p/n 0644-333)
Oil Filter Wrench(Adjustable) (p/n 0644-389)
Oil Injection Usage Tool (p/n 0644-007)
Oil Seal Installation Tool (p/n 0644-219)
Pinion Shimming Tool
(650/700 cc Engines) (p/n 0644-055)
Blind-Hole Bearing Puller (p/n 0644-500)
Piston Pin Puller (p/n 0644-328)
Rigid Hone Stone Set (2.7-4.1 in.) (p/n 0644-043)
Ring Compressor (p/n 0644-378)
Spring Tool (p/n 0644-072)
Starter Assembly Tool (p/n 0644-052)
Stud Runner (6, 8, & 10 mm) (p/n 0644-018,019,020)
Surface Plate (p/n 0644-016)
V Blocks (p/n 0644-022)
Valve and Spring Retainer Tool (p/n 0644-448)
Water Pump Bearing & Seal Kit (p/n 0644-502)
Battery Charger (p/n 0436-634)
Oil Pressure Test Kit (p/n 0644-495)
Compression Tester Kit (p/n 0444-213)
Fuel Pressure Test Kit (p/n 0644-493)
EFI Analyzer (p/n 0644-342)
EFI Analyzer Update Kit (p/n 0744-046)
EFI Analyzer Test Harness (p/n 0644-181)
Test Harness Kit (p/n 0644-506)
EFI Analyzer Test Harness (p/n 0639-624)
Engine Timing Gauge (p/n 0144-009)
Ignition Test Plug (p/n 0144-306)
Multimeter (Fluke Model 73 w/Case) (p/n 0644-191)
Peak Voltage Reading Adapter (p/n 0644-307)
MaxiClips (p/n 0744-041)
Tachometer (p/n 0644-275)
Timing Light (p/n 0644-296)
Vacuum Test Pump (p/n 0644-131)
Laptop Diagnostic Tool (p/n 0744-048)
Alcohol Test Kit (p/n 0644-044)
Carburetor Adjustment Screwdriver (90°) (p/n 0644-289)
Synchronizer Repair Kit (p/n 0644-062)
Carburetor Synchronizing Tool Adapter (p/n 0644-023)
Chip Puller (p/n 0644-188)
Fuel Pump Socket Wrench (p/n 0644-364)
Gas Gauge Removal Tool (p/n 0644-357)
Carburetor Tool Set (Mikuni) (p/n 0636-072)
Throttle Position Sensor (TPS)
Adjustment ToolKit (p/n 3639-891)
Bearing Cap Seal Protector (p/n 0644-268)
Bearing Cap Seal Protector (p/n 0644-403,404)
Bearing Removal Tool (p/n 0644-421)
Bearing Removal andInstallation Tool (p/n 0644-167)
Brake Disc Socket Wrench (ACT Drive) (p/n 0644-415)
Brake Disc Socket Wrench (ACT Drive) (p/n 0644-481)
Gear Case Drain Plug (p/n 0644-504)
Carbide & Stud Specifications Gauge (p/n 1639-632)
Clutch Alignment Bar (p/n 0644-320)
Clutch Alignment Bar (p/n 0644-246,428,427,496)
Clutch Compressor (p/n 0644-420)
Clutch Compressor (Arctic Round-Shaft) (p/n 0644-245)
Clutch Compressor (Comet) (p/n 0644-123)
Drive Clutch Bolt Tool (1/2-in. Drive) (p/n 0644-281)
Clutch Puller (Arctic) (p/n 0644-207)
Clutch Puller (Comet) (p/n 0644-096)
Clutch Puller (Comet) (p/n 0644-100)
Clutch Puller (4-Roller) (p/n 0644-446)
Drive Belt Deflection Tool (p/n 0644-412)
Drive Belt Deflection Tool (p/n 0644-424)
Drive Belt Gauge (p/n 0644-443)
Drive Belt Replacement Tool (p/n 0644-435)
Drive Clutch Spanner Wrench (p/n 0644-136)
Driven Pulley Puller (p/n 0744-023)
Driven Pulley Puller - ACT (p/n 0644-469,468)
Driven Pulley Compressor Tool (p/n 0644-444)
Driven Pulley Spring Adjustment Tool (p/n 0644-413)
Reverse Gear Adjustment Gauge (p/n 0644-244)
Roller Pin RemovalTool (p/n 0644-276)
Spider Removal Kit (p/n 0644-449)
Spider Removal Kit (4-Roller) (p/n 0644-505)
Track Clip Installation Tool (p/n 0644-194)
Track Stud HoleDrill (7 mm) (p/n 1639-629)
Ball Joint Fork (p/n 0644-098)
Idler Wheel Alignment Tool (p/n 0644-228)
Idler Wheel Puller Kit (p/n 0644-122,400)
Floating Piston Location Gauge (p/n 0644-350)
Floating Piston Removal Tool (p/n 0644-348)
Floating Piston Installation/Location Tool Kit (p/n 0644-402)
Gas Shock Retaining Blocks (Zero Pro) (p/n 0644-486)
Gas Shock Rod/BodyClamping Tool (p/n 0644-425)
Inflation Needle (p/n 0744-020)
Inflation Needle Replacement (p/n 0644-162)
Nitrogen Regulator (p/n 0644-151)
Piston Location Tool (p/n 0644-169)
Shock Absorber Air Pump (p/n 2603-614)
Rear Shock Adjuster (p/n 0644-015)
Shock Spanner Wrench (p/n 0644-447)
Shock Spanner Wrench (p/n 0644-398)
Shock Spanner Wrench (p/n 0644-305)
Shock Spring Removal Tool (p/n 0644-057)
Spanner Wrench - Fox Float Shock (p/n 0644-453)
Rear Axle Nut Socket (p/n 0644-399)
Axle Nut Spanner Wrench (p/n 0644-454)
Ski Alignment Tool (p/n 0644-457)
Rear Suspension Spring Tool (p/n 0144-311)
Hex Bits (1/4 in. Hex Drive) (p/n 0644-317,316)
Insert Holder (5/16 in.) (p/n 0644-315)
Jack Stand (p/n 0644-076/2639-799)
Phillips-Head Bits (1/4 in. Hex Drive) (p/n 0644-319,318)
(p/n 0644-308)
Replacement Bolt (Side) (p/n 0644-101)
Replacement Rivnuts (p/n 0623-557,582/627,581)
(p/n 0623-699,874,529/779)
Rivnut Tool (p/n 0644-232)
Rivnut Tool Insert Bit (p/n 0644-233,405,430,431)
Side Guard Kit (p/n 0639-611)
T-Handle Wrench (p/n 0644-257,024,025,026)
T Wrench (p/n 0644-021)
Torx Bit Insert (5/16 in. Hex Drive) (p/n 0644-314)
Torx Bits (1/4 in. Hex Drive) (p/n 0644-312,393,215,313)
Angle Finder Ball Hone
0644-097 0644-290 (60-64 mm)
0644-291 (65-70 mm)
0644-292 (72-74 mm)
0644-293 (76-83 mm)
0644-294 (83-88 mm)
Usage: Usage:
Identify levelness and pitch. Deglaze Nicosil plated cylinders. All are 320 grit and are recommended for reconditioning all Arctic Cat snowmobile engine cylinders (1976-2000).
Coolant Cap (Non-Pressurized) Fan Spanner Wrench (Suzuki)
0644-156 0644-340
Usage: Usage:
Fill cooling system on the 1992, 1995, and 1996 models equipped with bleed system. Hold fan in place during disassembly and assembly.
Flywheel Spanner Wrench Duck-Foot T-Handle Wrench (8 mm)
0144-007 0644-332
Usage: Usage:
Hold starter cup while removing/installing flywheel nut. Adjust oil-injection pump mechanical linkage.
EFI Throttle Cable Jam Nut/Oil-Injection Pump Jam Nut Wrench (10 mm) Engine Stand
0644-242 0644-079
Usage: Usage:
Loosen and tighten jam nuts on both the oilinjection pump and EFI throttle cable. Hold engine during assembling/disassembling.
Exhaust Spring Pliers (0°) Exhaust Spring Pliers (90°)
0644-391 0644-397
Usage: Usage:
Remove/install exhaust springs. Remove/install exhaust springs.
Crankshaft Protector Cap Flywheel Puller
0644-234 0744-040 (Complete Set)
0643-086 (Body)
0643-087 (Bolt)
0423-482 (6 mm Cap Screw)
0423-483 (8 mm Cap Screw)
Usage: Usage:
Protect the crankshaft end during flywheel removal. Pull flywheel off crankshaft on all Arctic Cat 2-stroke models.
Flywheel Puller Flywheel Puller Insert
0644-480 (Complete Set)
0644-122 (Wrench)
0644-133 (Bolt)		 0644-179
Usage: Usage:
Pull flywheel off crankshaft on Jaguar Z1. Protect the crankshaft end on the 900 cc engine during flywheel removal.
Crankshaft Bearing Remover Idle Speed Screw Jam Nut
0144-302 0644-311
Usage: Usage:
Remove crankshaft bearings. Loosen/tighten idle speed screw jam nut on batteryless EFI system.
Linkage Wrench (8 mm) Oil Filter Wrench (Adjustable)
0644-333 0644-389
Usage: Usage:
Adjust oil-injection pump mechanical linkage. Remove oil filters from 4-stroke engines. Features adjustments between 62-96 mm.
Oil Injection Usage Tool Oil Seal Installation Tool
0644-007 0644-219
Usage: Usage:
Measure exact amount of oil used by the oil injection pump during a given time period. Install the oil seal on the water pump driveshaft on the 440, 550, 580, 650, 700, 800, and 900 cc Arctic Cat engines.
Pinion Shimming Tool Blind-Hole Bearing Puller
0644-055 0644-500
Usage: Usage:
Determine size and number of pinion gear shims. Remove bearing from water pump on Jaguar Z1.
Piston Pin Puller Rigid Hone Stone Set (2.7-4.1 in.)
0644-328 (Complete Set)
0643-073 (Extractor Nut Only-Small)
0643-074 (Extractor Nut Only-Medium)
0643-075 (Extractor Nut Only-Large)
0643-072 (Threaded T-Handle)		 0644-043
Usage: Usage:
Remove piston pins. Replacement stones for Cylinder Hone Set (p/n 0644-041).
Ring Compressor Spring Tool
0644-378 0644-072
Usage: Usage:
Compress piston rings for cylinder installation. Features a quick-release function for removing tool from underside of piston. Remove/install exhaust springs.
Starter Assembly Tool Stud Runner
0644-052 0644-018 (6 mm)
0644-019 (8 mm)
0644-020 (10 mm)
Usage: Usage:
Hold brushes for assembling UTC brand starter motor. Install studs on cylinders and crankcase.
Surface Plate V Blocks
0644-016 0644-022
Usage: Usage:
True sealing surfaces. Check crankshaft runout.
Valve and Spring Retainer Tool Water Pump Bearing & Seal Kit
0644-448 0644-502
Usage: Usage:
Adjust intake valve and exhaust valve “lash clearance” (2003-2006 660 cc 4-stroke engines). Remove/install crankcase water pump bearings and seals.
Battery Charger Oil Pressure Test Kit
0436-634 0644-495 (Complete Kit)
0644-371 (8 mm Adapter)
0644-372 (10 mm Adapter)
0644-373 (12 mm Adapter)
Usage: Usage:
Charge sealed, maintenance-free batteries. Test oil pressure on all Arctic Cat 4-stroke engines.
Compression Tester Kit Fuel Pressure Test Kit
0444-213 (Complete Kit)
0444-207 (10 mm Adapter)
0444-093 (12 mm Adapter)		 0644-493
Usage: Usage:
Test cylinder compression on all Arctic Cat engines. Test fuel pressure on both EFI and carbureted models. A valuable tool for troubleshooting EFI fuel systems.
EFI Analyzer EFI Analyzer Update Kit
0644-342 (Complete Kit)
0644-422 (Harness)
3005-101 (Harness)
0643-124 (EPROM)
1686-310 (Harness)		 0744-046 (Complete Kit)
0643-124 (EPROM)
1686-295 (Harness)
1653-368 (Instructions)
Usage: Usage:
Troubleshoot 1992-2007 2-stroke Arctic Cat EFI systems including models with an exhaust temperature sensor (except 2007 800 cc/1000 cc). Troubleshoot 1992-2007 2-stroke Arctic Cat EFI systems including models with an exhaust temperature sensor (except 2007 800 cc/1000 cc).
EFI Analyzer Test Harness Test Harness Kit
0644-181 0644-506 (Complete Kit)
0644-497 (A. Laptop Harness)
0644-498 (B. Chassis Control Harness)
0644-499 (C. Chassis Control Harness)
Usage: Usage:
Troubleshoot EFI battery system (1993-1996 models). To attain diagnostic information on 2007 EFI models. p/n: 0644-497 (A) Usage: Adapt laptop computer to 2007 800 cc/1000 cc engines to attain diagnostic information. p/n: 0644-498 (B) Usage: Read chassis control unit codes on 2007 800 cc/ 1000 cc 2-stroke engines and 1100 cc 4-stroke engine. p/n: 0644-499 © Usage: Read chassis control unit codes on 2007 500 cc/ 600 cc engines.
EFI Analyzer Test Harness Engine Timing Gauge
0639-624 0144-009
Usage: Usage:
Troubleshoot EFI battery system (1997-1998 models). Static time engines without CDI ignition.
Ignition Test Plug Multimeter (Fluke Model 73 w/Case)
0144-306 0644-191
Usage: Usage:
Test engine ignition. Ditgital multimeter accurate to within ± 0.5%.
Peak Voltage Reading Adapter Torx Bits (1/4 in. Hex Drive)
0644-307 0644-312 (#25)
0644-393 (#27)
0644-215 (#30)
0644-313 (#40)
Usage: Usage:
With Fluke Model 73 Multimeter (p/n 0644-191),read peak voltage. With Quick-Disconnect Coupler (p/n 0644-308), remove and install torx-head screws.
MaxiClips Tachometer
0744-041 0644-275
Usage: Usage:
Insulation-piercing test clips for quick, accurate electrical testing. A valuable tool for cutting testing time. Measure engine RPM for 2-stroke and 4-stroke engines.
Timing Light Vacuum Test Pump
0644-296 0644-131
Usage: Usage:
Check ignition timing. Check components for air leaks.
Laptop Diagnostic Tool Alcohol Test Kit
0744-048 0644-044
Usage: Usage:
Troubleshoot 660 cc/1100 cc 4-stroke and 800 cc/1000 cc 2-stroke electrical and fuel systems. Test gasoline for alcohol.
Carburetor Adjustment Screwdriver (90°) Synchronizer Repair Kit
0644-289 0644-062
Usage: Usage:
Make carburetor adjustments on all twin and triple cylinder engines. Will be especially useful for adjusting the pilot circuit screw on all TM-style carburetors. Replacement components for Carburetor Synchronizer(p/n 0644-069).
Carburetor Synchronizing Tool Adapter Chip Puller
0644-023 0644-188
Usage: Usage:
Threads into carburetor fitting and slides into synchronizer hose. Safely remove EPROM chip from the ECU on all EFI models.
Fuel Pump Socket Wrench Gas Gauge Removal Tool
0644-364 0644-357
Usage: Usage:
Remove plastic nut securing the fuel pump to the gas tank. Remove gauge from the gas tank.
Carburetor Tool Set (Mikuni) Throttle Position Sensor (TPS) Adjustment Tool Kit
0636-072 3639-891 (Complete Set)
0686-999 (Harness Only)
0644-359 (Torx-Head Screwdriver - #25 Only)
0644-344 (Torx-Head Screwdriver - #30 Only)
0644-345 (Pin Gauge Only)
Usage: Usage:
Disassemble/assemble Mikuni carburetors. Precisely adjust the throttle position sensor on carbureted and EFI models.
Bearing Cap Seal Protector Bearing Cap Seal Protector
0644-268 0644-403 (1/2 in.)
0644-404 (5/8 in.)
Usage: Usage:
Protect cap seal on rebuildable shock absorbers through 2002 models. Protect cap seal on rebuildable shock absorbers on 2003 and newer models.
Bearing Removal Tool Bearing Removal and Installation Tool
0644-421 0644-167
Usage: Usage:
Remove chain case bearings on 2003 and newer models. Remove and install bearings in the driven clutch movable sheave and button plate.
Brake Disc Socket Wrench (ACT Drive) Brake Disc Socket Wrench (ACT Drive)
0644-415 0644-481
Usage: Usage:
Remove/install brake disc on 2004-2006 ACT Drive models. Remove/install brake disc on 2007 ACT Drive models.
Gear Case Drain Plug Carbide & Stud Specifications Gauge
0644-504 1639-632
Usage: Usage:
Drain lubricant/flush fluid from the gear case on ACT Drive models. Check stud length and carbide angle.
Clutch Alignment Bar (1.365 in. Offset) Clutch Alignment Bar (1.562 in. Offset)
0644-320 0644-246
Usage: Usage:
Align the drive clutch and driven pulley on models using the reverse cam driven pulley. Align drive clutch and driven pulley on 1997 models using the Arctic internal-helix driven pulley.
Clutch Alignment Bar (1.485 in. Offset) Clutch Alignment Bar (1.655 in. Offset)
0644-428 0644-427
Usage: Usage:
Align drive clutch and driven pulley on Bearcat Wide Track Turbo model. Align drive clutch and driven pulley on 10.0 in. ACT roller driven pulley models.
Clutch Alignment Bar (1.507 in. Offset) Clutch Compressor
0644-496 0644-420
Usage: Usage:
Align drive clutch and driven pulley on 10.4 in. ACT roller driven pulley models. Compress and hold drive clutch in the compressed position for changing cam arms and removing/installing six-post drive clutch on AWS VI models.
Clutch Compressor (Arctic Round-Shaft) Clutch Compressor (Comet)
0644-245 0644-123
Usage: Usage:
Compress and hold Arctic round-shaft drive clutch in the compressed position for changing cam arms. Compress and hold drive clutch in the compressed position for changing cam arms.
Drive Clutch Bolt Tool (1/2-in. Drive) Clutch Puller (Arctic)
0644-281 0644-207
Usage: Usage:
Compress and hold drive clutch in the compressed position for changing cam arms. Remove Arctic round-shaft drive clutch from the crankshaft.
Clutch Puller (Comet) Clutch Puller (Comet)
0644-096 0644-100
Usage: Usage:
Remove Comet drive clutch (short bolt w/retainer plug style). Remove Comet drive clutch (long bolt style).
Clutch Puller (4-Roller) Drive Belt Deflection Tool
0644-446 0644-412
Usage: Usage:
Remove 4-roller drive clutch on 2007 1000 cc 2- stroke engine and 1100 cc 4-stroke engine. Adjust driven pulley for proper drive belt deflection and aid in drive belt removal on models using the ACT Roller Driven Pulley.
Drive Belt Deflection Tool Drive Belt Gauge
0644-424 0644-443
Usage: Usage:
Adjust driven pulley for proper drive belt deflection and aid in drive belt removal on 2004 440 Sno Pro model. Measure drive belt width.
Drive Belt Replacement Tool Drive Clutch Spanner Wrench
0644-435 0644-136
Usage: Usage:
Replace drive belt and adjust belt deflection on models using the ACT Roller Driven Pulley. Hold Comet and Arctic round-shaft drive clutch in place during removal and installation.
Driven Pulley Puller Driven Pulley Puller - ACT
0744-023 0644-469 (Left-Hand Thread)
0644-468 (Right-Hand Thread)
Usage: Usage:
Remove driven pulley from driven shaft. It can be used on both the roller and button style. Remove ACT Driven Pulley from a corroded input shaft. Left-hand thread for models with a white sheave adjuster. Right-hand thread for models with a black sheave adjuster.
Driven Pulley Compressor Tool Driven Pulley Spring Adjustment Tool
0644-444
0644-439 (A. Compressor Assembly Only)
0643-095 (B. Disc Only)		 0644-413
Usage: Usage:
Disassemble/assemble Arctic ACT and Team Industries roller driven pulleys. Adjust driven pulley spring pre-load on models using the ACT Roller Driven Pulley.
Reverse Gear Adjustment Gauge Roller Pin Removal Tool
0644-244 0644-276
Usage: Usage:
Adjust reverse gear linkage on all 1996-2002 reverse gear transmissions. Remove roller pins from retainer plate on driven pulley.
Spider Removal Kit Spider Removal Kit (4-Roller)
0644-449 (Complete Kit)
0744-037 (Handle)
0744-036 (Removal Tool)
0644-380 (Clutch Holder - 33 mm)
0744-035 (Clutch Holder - 30 mm)
0644-138 (Thin Wall Deep Socket - 1 7/16 in.)		 0644-505 (Complete Kit)
0644-473 (Clutch Holder - 35 mm)
0644-474 (Removal Tool)
Usage: Usage:
Disassemble/assemble/remove spider on Comet and Arctic drive clutches. p/n: 0644-380 (33 mm) Usage: Hold clutch stationary sheave for 33 mm crankshaft on 2001 and later 800/900 cc and 2003 and later 700 cc “Laydown” engines. p/n: 0744-035 (30 mm) Usage: Aid in assembling/disassembling of 108 & 102C Comet and Arctic drive clutches. p/n: 0644-138 (1 7/16 in.) Usage: Remove and install spider nut on Arctic roundshaft drive clutch. Disassemble/assemble/remove spider on 4-roller drive clutch.
Track Clip Installation Tool Track Stud Hole Drill (7 mm)
0644-194 1639-629
Usage: Usage:
Install track clips on Camoplast and Yokohama rubber tracks. Drill 7 mm hole through rubber tracks for installing studs.
Ball Joint Fork Idler Wheel Alignment Tool
0644-098 0644-228
Usage: Usage:
Separate ball joint from spindle or drag link. Align center idler wheels during replacement without removing the suspension.
Idler Wheel Puller Kit Floating Piston Location Gauge
0644-122 (Complete Kit - 6 in.)
0644-400 (Complete Kit - 8 in.)
0644-114 (A. Handle - 6 in.)
0644-401 (A. Handle - 8 in.)
0644-111 (B. Insertion Tool)
0644-120 (C. Pivot Plate)
0644-118 (D. Adapter Plate)
0623-310 (E. Cap Screw)
0644-119 (F. Puller Bolt) - 6 in. Kit
0644-432 (F. Puller Bolt) - 8 in. Kit		 0644-350
Usage: Usage:
Remove/install skid frame idler wheels. Precisely locate and measure floating piston depth without use of a calipers.
Floating Piston Removal Tool Floating Piston Installation/Location Tool Kit
0644-348 0644-402
Usage: Usage:
Remove floating piston from cross-link suspension shocks on 2002 models. Install/locate floating piston from rebuildable gas shock absorbers. Precisely locate and measure floating piston depth without use of calipers.
Gas Shock Retaining Blocks(Zero Pro) Gas Shock Rod/Body Clamping Tool
0644-486 0644-425
Usage: Usage:
Hold Zero Pro shock secure during disassembly and assembly. Hold gas shock absorber for servicing.
Inflation Needle Inflation Needle Replacement
0744-020 0644-162
Usage: Usage:
Pressurize rebuildable gas shock absorbers with nitrogen. Replacement needle assembly for Inflation Needle (p/n 0744-020).
Nitrogen Regulator Piston Location Tool
0644-151 0644-169
Usage: Usage:
Recharge rebuildable gas shock absorbers. Precisely locate the floating piston in the rebuildable gas shock absorber.
Shock Absorber Air Pump Rear Shock Adjuster
2603-614 0644-015
Usage: Usage:
Adjust air pressure on Fox Air Shocks. Rotate rear shock adjusting cam on external AFS models.
Shock Spanner Wrench Shock Spanner Wrench
0644-447 0644-398
Usage: Usage:
Adjust pre-load on Fox Zero Pro shock absorber. Adjust pre-load on front arm rebuildable shock absorber.
Shock Spanner Wrench Shock Spring Removal Tool
0644-305 0644-057
Usage: Usage:
Adjust pre-load on front arm standard shock absorber. Remove/install shock absorber spring.
Spanner Wrench - Fox Float Shock Rear Axle Nut Socket
0644-453 0644-399
Usage: Usage:
Remove and install the bearing cap on Fox Float shocks (2005). Loosen/tighten rear axle nut on 2004 and earlier AWS VI models.
Axle Nut Spanner Wrench Ski Alignment Tool
0644-454 0644-457
Usage: Usage:
Adjust track alignment/tension (2005 440 Sno Pro). Make quick, accurate measurements for precise ski alignment. A valuable tool for saving time.
Rear Suspension Spring Tool Hex Bits (1/4 in. Hex Drive)
0144-311 0644-317 (5 mm)
0644-316 (6 mm)
Usage: Usage:
Install/remove rear suspension springs. With Quick-Disconnect Coupler (p/n 0644-308), remove and install bolts and screws.
Insert Holder (5/16 in.) Jack Stand
0644-315 0644-076 (Standard Models - Low)
2639-799 (ETT Models - High)
Usage: Usage:
With Torx Bit Insert (p/n 0644-314), remove and install torx-head screws. Support rear of snowmobile off the ground.
Phillips-Head Bits (1/4 in. Hex Drive) Quick-Disconnect Coupler
0644-319 (#2)
0644-318 (#3)		 0644-308
Usage: Usage:
With Quick-Disconnect Coupler (p/n 0644-308), remove and install Phillips-head screws. Hold 1/4 in. hex drive Torx Bits (page 26), Hex Bits (page 24), and Phillips-Head Bits (page 24).
Replacement Bolt (Side) Replacement Rivnuts
0644-101 0623-557 (1/4 x 20)
0623-582 (1/4 x 20)
0623-627 (1/4 x 20)
0623-581 (5/16 x 18)
0623-699 (3/8 x 16)
0623-874 (8-32)
0623-529 (10-32)
0623-779 (10-32)
Usage: Usage:
Replaces side bolt in Track Clip Tool (p/n 0144-301). With Rivnut Tool (p/n 0644-232), replace rivnuts.
Rivnut Tool Rivnut Tool Insert Bit
0644-232 0644-233 (1/4 x 20)
0644-405 (10-32)
0644-430 (5/16 x 18)
0644-431 (3/8 x 16)
Usage: Usage:
Collapse and install rivnuts. With Rivnut Tool (p/n 0644-232) and Replacement Rivnuts, replace rivnuts.
Side Guard Kit T-Handle Wrench
0639-611 0644-257 (8 mm)
0644-024 (10 mm)
0644-025 (12 mm)
0644-026 (14 mm)
Usage: Usage:
With Jack Stand (p/n 0644-076/0639-462). Remove and install nuts and bolts.
Torx Bit Insert (5/16 in. Hex Drive) T Wrench
0644-314 0644-021
Usage: Usage:
With Insert Holder (p/n 0644-315), remove and install torx-head screws. Drive 3/8 in. square-drive sockets.